EP model alternative gearbox for woods rotary gearbox
NEW forty HP GEARBOX Sleek Input 1 three/eight twelve spline output Interchangable with market common dimension i.e.: OMNI GRIZZLEY CHEETAH HOWSE KING KUTTER BUSH HOG HICO SILVER EDGE Several Much more
Attributes
(one) manufacturer new forty five horse energy shearpin gearbox. This gearbox fits a number of various tends to make of 4′,5′ and some 6′ rotary cutters. I sell a whole lot of these boxes each and every year for many different programs and carry ALL Replacement Elements for this box, but hopefully you is not going to have to be concerned about that.
Right here are the specs on the box:
*45 horse electrical power gearbox
*Regular 1-3/eight” easy input shaft(where the pto shaft hooks on). The pto shaft is held on by a one/2 shearbolt.
*duration of the input shaft out of the gearbox is 3″ prolonged
*bolt hole pattern for mounting is on the corners, 4-three/4 middle of hole to heart of hole. It normally takes a 5/eight” bolt.
*twelve splined output shaft(the place the blade carrier hooks up on the bottom)
*1-nine/sixteen outside measurement over the output shaft splines- from the base of the output cap to the stop of the splines is 2-3/four” long- overall duration of the output shaft is 4-one/two” extended.
*will take a 1″ threaded castle nut and a carter key on the bottom of the output shaft to protected blade pan(NUT is included – – BLADE PAN IS NOT!!)
*overall peak of the box from the best of the mower deck to the best of the box is 9-one/2″
This is a fairly weighty merchandise (forty seven lbs.) so freight is not low cost, but we do not make something off of freight, no matter what ups fees us we demand you.
40 HP
one:1:47 Ratio
one-3/8″ Clean Input Shaft with Shear Pin Gap
1-1/two” 12-Spline Ouput Shaft
Bolt Sample: six-one/two” (4) five/8″ Holes, five” Centre Hole Required for Shaft Assembly
The Enter and Output Shafts Cannot be Acquired Serparately.
They are Sold as a package.
The kit includes the following elements: input shaft, input gear, output shaft, output gear.
The Shaft Package Are not able to Be Divided.
EP manufacturer substitution gearbox for woods rotary gearbox
Rotary Cutter Gearbox Troubleshooting Manual
Is your mower leaking, creaking or in any other case executing incorrectly? You have appear to the appropriate area.
Read through underneath for the most typical concerns with rotary cutter gearboxes and their options (from quick and filthy, to specialist).
Leaking Bottom Seal:
If you’ve got wrapped some baling or fencing wire all around your output shaft and blown the seal, the professional thing to do is to substitute the seal.
If your output seal is intact, and you are ready to get ID, OD and thickness measurements (in millimeters), most bearing homes can purchase you up a generic double-lip seal that will get you again up-and-running. If not, give us a contact and we can support you kind out what you need to have.
A dental choose is the best way to remove the outdated seal 
ahead of urgent in the new one.
If you might be lucky ample to have a slow-leak, the fast and dirty technique is to operate automotive-type grease in the gearbox until the new seal comes in. Be certain to check out and insert grease much more often than you would with oil, as this is NOT a professional repair.
Broken Output Shaft:
Uh oh. You strike some thing that didn’t shift. The very good information is that the output shaft on most gearboxes is fairly straightforward to exchange. The bad news is… it truly is not often an isolated failure.
The first issue to do is to take aside your gearbox and assess the entire extent of the harm. If it is really just the output shaft, you should be ready to alter it out, no problem. The output shafts start off at about $70 and go up in price based on the size of the gearbox.
However, in most situations, the bearings ($twenty/ea), seals ($10/ea) and gear-established ($70) will also generally get a beating. If you’re unfortunate, the output cap ($80) will also endure some damage.
In this circumstance, it is normally cheaper to replace the gearbox. Examine the cost of elements to the expense of an complete, new, warrantied gearbox. Often, even professionals have to know when to call it a working day.
I Want to Modify my Enter Shaft:
If you are tired of shifting shear pins or searching again and viewing that your mower hasn’t been chopping, you may possibly want to put in a slip-clutch pto shaft (Sure, we promote these as well).
This generally requires setting up a 540-style, six-spline input shaft ($eighty five) on your mower’s gearbox.
Lucky for you, we did a create-up on our weblog. It’s referred to as “How to change the enter shaft on your rotary cutter gearbox”.
My Gearbox is Groaning/Creaking:
“Groaning”, “creaking”, or “popping” all audio type-of similar above-the-telephone. The best factor to do is to disassemble your gearbox and get a appear at the gears and bearings. The problem will usually existing by itself in the way of damaged/missing gear enamel, toasted gears (like that photograph on our home page), or blown bearings.
If every little thing appears regular, try altering the gear-mesh. This is accomplished with the mylar “gaskets” that sit in between the major gearbox circumstance and the enter/output caps. Try adding or getting rid of some of these spacers right up until your gears have about 1/8″-1/four” of free perform. Pros can order replacements ($1-two) in various thicknesses, but we advise the rapid and soiled approach of reducing your own out of a sheet of mylar.
Do not fail to remember to re-seal the gearbox with RTV after you’ve identified the appropriate blend. Even although they are known as “gaskets”, they won’t seal your gearbox on their possess.
Gearbox Aluminium Multiplier implies various points to various individuals, so examine out our interpretation here http://agricultural-gearbox.xyz/agricultural-gearbox/gearbox-and-reducer-for-crop-storage-drive.html.