The EP Series Helical Bevel Reducer provides unmatched performance, durability, and design flexibility. This unit provides torque capacities up to 20,000 Nm (14,750 ft pounds).
The cat4CAD software enables simple interactive product collection of the complete gearbox and gear-electric motor system. Cat4CAD facilitates you in selecting and configuring these products, gives you the opportunity to print out considerable technical data linens, and generates complete 2D drawings and 3D versions for direct download.
11 sizes
Input power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty course F insulated motor windings
Course 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and better torques in smaller sized sizes.
Multiple Input Options: Integral gear motors, inch or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple Output Choices: Hollow bores and shrink disks for shaft installation, inch and metric result shafts, mounting pilots and flanges offer an array of design solutions.
UNIBLOCK Housing: For optimum rigidity, universal mounting on five sides or with a torque arm.
Worldwide Motor: Multiple leads and windings for globally multi volt/Hz requirements in addition modular design to accept brakes, encoders or forced cooling.
High efficiency engine design available
Innovative self-locking, self-aligning taper shaft engine connection
Gearbox supplied factory filled up with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple locations (Optional OtN2000)
Double lip seals on heat treated, plunge ground shafts
Shaft mounting choices include tapered bushings designs
This is a comprehensive offering of energy-efficient, right angle helical bevel enclosed gearing. It is obtainable as gearmotors and a variety of reducers with torque capacities up to 119,000 inch pounds. Housing styles include footed, face and flanged configurations. Gearmotors can be found in three phase high efficiency styles through 50 HP and single phase to 5 HP. We provide a variety of input and output shaft choices. Additionally, you will find fixed and variable rate motors and selection of ratios obtainable in this product offering.
Features
Accommodates input power from ΒΌ Hp to 75Hp
Torque rankings up to 119,489 in-lbs
Reduction ratios up to 7,500:1
Helical – bevel – helical gear train offers cost effective high and low speed solutions
Up to 94% efficient
Four input possibilities for all units
Two output flange choices – B5 and B14
Multiple output shaft interfaces
Vital dimensions interchangeable with main competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
Heavy Duty Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and Forest
Unit and Baggage Handling
Water and Wastewater
As per the growing and varying demands of customers, we offer a wide selection of Helical Bevel Gear Reducers. The technological content material of our products allows for an extraordinary efficiency/lifespan ratio. The extremely versatile Helical Bevel Gear Reducers we provide are successfully found in a vast number of commercial and civil applications. They are B-Series units which offer excellent value for money and result torque/weight ratio, especially considering that they need not a lot of servicing. Besides these, our products can be found in cast iron (sizes 063 to 163) or aluminium (sizes A42 to A73) casing.
Features:
Sizes: 
060-080-100-125-140-150-160
Available versions: B-fitted for engine coupling, IB with input shaft, CB with small motor, PB-fitted for electric motor coupling with flexible joint
Casing with ft FC, flange SC and general UC
Power up to 90 kW
Gears hardened and tempered with shaved or ground profile
Gearing with 3 reduction stages
Gleason spiral bevel equipment pairs with run-in profile, mounted as second decrease stage for an increased resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-power casings optimized with FEM evaluation and input and output flanges of grey cast-iron G200 to ensure best level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue epoxy-polyester powder
Accessories: torque arm, output flange, output shaft, shrink disk, backstop device, protection cover kit, viton essential oil seals, reinforced result, assemble/disassemble kit
Series EP right position helical bevel equipment motors offer ratios from 8:1 to 160:1 in three phases or up to 10000:1 in five stages. Motors are available up to 90kW and output torque capability up to 12,300 Nm.
The series EP helical bevel gear motor was created with integral cast feet for base or end mounting and can be offered with single or dual extended output shafts.
Products are also available since shaft mounted or with result flanges and are designed for installation horizontally or vertically. The models can also be offered with a bolt on torque response helical bevel gear reducer bracket and all variants are available either motorised or with an insight shaft assembly.
Adding to the new selection of Ever-Power helical gear motors the product takes advantage of our a long time of accumulated design knowledge together with the use of high quality materials and elements. The end result is a number of speed reducing geared motors offering high load carrying capacities, increased efficiency, silent running and reliability.
Top features of Helical Bevel Gear Motor
Standard motor connection
Capability to fit double oil seals, on input and output shaft as required.
All products are dimensionally interchangeable with additional major manufacturers.
Units are manufactured and assembled from a family of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units could be fitted with a backstop module and reducer Models can be installed with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are used in industries such as chemical substances, pharma, packaging, food processing, plastic-type material and automation etc.
Key Features:
Sizes: A40-A50-A70
Offered versions: EP – fitted for electric motor coupling, IEP – with input shaft, CEP – with small motor
Cases with ft, flange or universal
Switch on to 4,8 Kw
Gears with shaved or surface profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in die-cast aluminium alloy
Excellent mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in in accordance to DIN 1843
Accessories: torque arm, result flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission device and made up of Y series electric motor, helical gear,Arc gear and worm gear. The gears are constructed with high wear-resisting alloy materials, specifically and finely processed.
Advantages:
1: Helical-bevel gear two-stage reducer
2: Compact structure, high efficiency
3: Quenched 20CrMnTi for gears
4: CE, ISO9001.
5: Small design, small volume, wonderful appearance ,and strong capacity to be overloaded.
6: Precise division and wide range for transmission ratio.
7: The efficiency is up to as high since 96% with low energy intake, strong adaptability and is with the capacity of operating continually in corrosive or damp environment.
8: All- purpose use, convenient and low-cost maintenance.
9: New seal gadget, strong adaptability.
10: Varied range of motor combinations, mouting positions and struture projects.